Download this free, 140-page Flexible Packaging Playbook jam-packed with strategies for success, best practices, and pitfalls to avoid.  Learn more »
Glenroy invites you to download this playbook.
Article |

Tray packer shrinks changeover time

Tray packing/shrink wrapping line for canned vegetables provides 55-tray/min speeds along with fast, no-tool changeover for Furman Foods.
Print Reprint
FILED IN:  Controls  > Strategy
     

After installing a new tray-packing and shrink-bundling line for canned tomato products Northumberland PA-based Furman Foods has reduced time required for changeover from three hours down to 45 minutes. While that may not seem especially fast to some plant engineer Ralph Lambert says it's fast given the amount of equipment involved. "Nobody else's machine in this class would be faster" he opines.

Although changeover time was an important factor in purchasing the line supplied by Arpac L.P. (Schiller Park IL) throughput was just as imperative. The new continuous-motion line reliably cranks out 12-pack shrink-bundled trays of cans at speeds of 45 to 55 tray-packs/min says Lambert. That's compared to 35/min on the line it replaced. Plus the new equipment only requires two workers vs three previously.

"We run a britestock operation" says Lambert. "We can vegetables [mostly tomatoes] put them on pallets with no label and inventory them. Then we will bring them out as the orders come in and label tray-pack shrink and palletize." Furman packs product under its own label as well as for private-label accounts.

Related Sponsored Content

Although the line produces mostly 12-packs (with some 24-packs for the smaller can sizes) the fast-change capability was needed to accommodate the range of can sizes from a 202x308 6-oz can to a 401x411 28-oz can. At the time of Packaging World's visit the line was packing 15-oz cans of the Furmano-brand Italian-style tomatoes.

Fast changeover

Key to the line's fast changeover capability is the collator which converts an incoming mass-flow of cans into groups of 12 or 24 (either a 4x3 or 4x6 pattern). Instead of relying on traditional lug chains to isolate groups of cans the collator uses what Arpac refers to as a pair of servo-driven "caterpillar" side lugs.

The key difference: There are no chains to remove and install for different can sizes. Instead servo motors automatically change the distance between the lugs in the machine direction after an operator selects a new can size from the touchscreen operator interface. Simple handwheels are used to widen the distance in the cross direction between the side lug belts that contain the cans on the left and right sides of the conveyor.

Handwheel adjustments are also used elsewhere on the machine for required manual adjustments. "It's essentially a no-tool changeover machine" says Lambert.

Adjustments that occur automatically when an operator selects a new can size include the speed and timing of the machine's servo-driven conveyors and flight bars. The timing and quantity of hot melt adhesive dispensed by the Nordson (Duluth GA) hot melt applicator is also changed electronically.

The shrink bundler is also designed for minimal downtime. Instead of using one roll the bundler draws film from two rolls simultaneously forming front and rear "walls" of film that are sealed together and shrunk around each tray pack. Further two additional rolls can be mounted right on the machine in a standby position reducing downtime to a quick five-minute splice. There's nothing especially unique about the low-density polyethylene 1.75-mil film says Furman.

ADVERTISEMENT

High throughput

Because the line is a continuous-motion system it allows a higher throughput compared to intermittent-motion machines says Lambert.

Illustrating how the machine maximizes throughput is the machine's ability to double-stack five trays at a time instead of one. Another example is the traveling seal bars on the wrapper which dwell on the heat-seal as they move with the tray.

Another important feature of the machine is the data acquisition software that Arpac wrote and which runs on the machine's PLC from Allen-Bradley (Milwaukee WI). Statistics on the machine's performance and operational history can be downloaded to an externa